A constantly running toilet is a common and easily overlooked household problem: the noise isn't loud, but water keeps running all day. Greater Toronto Area cities charge water bills based on usage, so a leaking toilet can add a significant amount to your monthly bill, which you notice when the seasonal bill arrives.
Good news: all parts in the toilet tank are simple and cost just a few to several dozen dollars at hardware stores like Home Depot, Canadian Tire, or RONA. Most repairs take less than 30 minutes to do yourself., No need to remove the toilet.
Find the small valve on the wall or floor behind the toilet.(Angle valve). Turn clockwise to shut off the toilet's water supply; turn it off before repair or when water is about to overflow.
First identify: which “漏” it is
| Symptoms | Most often | Can you fix it yourself |
| Water keeps flowing from the overflow tube long after flushing | Water level too high / faulty fill valve. | Yes, adjust the float or replace the fill valve. |
| After being quiet for a while, it refills on its own “哗” | Flapper leaks water | Yes, replace the rubber flapper. |
| Button/handle pressed but doesn't return | Zipper is too long or short, or the wrench is stuck | Yes, adjust the chain. |
| Water on the floor around the toilet base. | Broken wax ring at the base or loose toilet | If removing the toilet, it's best to hire a professional |
| Water leaking between tank and toilet, or at water supply connection | Screw washers are aging, hoses are damaged | Simple enough to replace the hose yourself. |
| The tank or toilet body has cracks | Cracked ceramic. | Cannot repair, need to replace the toilet |
A simple test: food coloring method
Not sure if water is leaking secretly from the tank into the bowl? Do a test.
- Open the tank lid and add a few drops of food coloring (or a bit of coffee) into the tank.
- Do not use water within 15–30 minutes.
- Check the water in the toilet bowl: if it's discolored, water is leaking from the tank, likely a flapper issue.
Flush after testing, the color will flush away and usually won’t stain.
Scenario 1: leaking flapper seal (most common)
The rubber piece at the bottom of the tank “Toilet lid” is the flapper. After years it hardens and deforms, sealing poorly, causing slow leaks. When the tank water level drops, the fill valve opens again—so you’ll hear it “哗” periodically.
How to replace
- Turn off the angle valve behind the toilet, flush once, empty the tank, and sponge out the remaining water.
- Remove old flapper from overflow pipe ears, unzip the chain from the handle.
- Take the old rubber flapper to the hardware store for a matching replacement., Common sizes are 2 inch and 3 inch; wrong size will still leak.
- When installing new flapper and hanging chain: chain should be slightly loose when button is released (1-2 links slack); too tight and flapper won’t seal, too loose and flapper won’t open properly.
- Open the angle valve, wait for the tank to fill, then do another dye test.
Before replacement, use your finger to feel the edge of the “Water outlet” under the gasket. If there is scale or burrs, gently clean it with a soft scouring pad; otherwise, the new gasket won't seal properly.
Scenario 2: water level too high, water continuously flows out through the overflow pipe
The vertical pipe in the middle of the tank is the overflow tube. If the water level is above the overflow tube, water will continuously flow into the toilet because the inlet valve never shuts off.
Adjust water level
- Normal water level is usually atAbout 2–3 cm below the overflow pipe opening(Typically a water level line marked inside the tank).
- Float cup typeInlet valve (most common now, cylinder fitted on the inlet pipe): has an adjustment rod or screw nearby, turn it down to lower the float cup and stop water at a lower level.
- Float ball type(Old type, one long rod connected to a large ball): gently bend the rod downward a bit, or turn the adjustment screw on the rod.
- Adjust and flush to see where water level stops.
If adjusting doesn't stop leak: replace inlet valve
After years, inlet valve seals age and fail to close properly; adjusting water level won't help. Complete fill valve sets are sold at hardware stores with diagrams:
- Turn off the angle valve and drain the water from the tank.
- Unscrew the nut connecting the fill hose outside the tank bottom (place a basin and towel below, it will drip).
- Unscrew the large plastic nut securing the fill valve at the tank bottom and remove the old one.
- Install a new one, adjust the height according to instructions, and tighten the nuts——Hand-tighten, then slightly tighten more; over-tightening plastic parts can cause cracks。
- Also replace the water supply hose with a new stainless steel braided one; old rubber hoses may burst.
- Open the angle valve and check all joints for leaks.
Scenario 3: button/handle issues
- Button/handle pressed but doesn't return, water keeps flushing: Zipper too tight or tangled, stuck on the flapper; loosen a section.
- Must hold down to flush properly: Zipper too loose, tighten a section.
- Wrench wobbles: Tighten the nut at the base of the wrench outside the tank (note this nut is oftenReverse thread., Tighten by turning in the opposite direction.
When to call a plumber
In these cases, DIY is not recommended.
- Water around toilet base, soft floor, water stains on ceiling below: Most likely the wax seal at the base is damaged, or there's a problem with the drain pipe under the floor. The toilet needs to be removed and reinstalled, and if the floor is water damaged, it must be repaired to prevent mold.
- Angle valve won't turn or leaks as soon as you turn it, or there's no angle valve at all: You need to turn off the main house valve before replacing it; replacing angle valves involves pipe connections.
- The tank or toilet has cracks: Cracks will only get bigger, replace the toilet.
- Toilet often clogs, flush is weak, and other drains bubble during flushing: Could be a drainage or main sewer pipe issue, see referenceHow much does Drain Clearing costand oursWhat to do if drain is clogged。
- For condos, if the toilet leaks to downstairs neighbors, notify property management first.
You can check typical call-out and hourly rates for plumbers first.Plumber Rates & Call-out Fees, Have an idea before comparing quotes.
Check the whole house while at it
The toilet is the biggest “Water theft” water user, but not the only one:
- Water meter test.: Note your water meter reading before bed when no one will use water, then check again in the morning. A change means there's a leak somewhere at home.
- Leaky faucet or showerhead: usually valve core or washer issue, minor repair.
- Water at Water Heaters base: may be safety valve or tank issue, see reference.What to do if Water Heaters has no hot water.。
- Before winter, turn off the valve inside for outdoor faucets and drain them, see referencePrevent frozen pipes。
Don't want to DIY?
Toilet repairs are small jobs that many technicians are happy to do if they're nearby. Post a free request below with details of “Toilet constantly running / base leaking”, your area, and convenient times; local technicians will quote, so you can compare and choose. A photo inside the tank helps them know what parts to bring.
FAQ
Does a constantly running toilet waste a lot of water?
Yes. A severe leak (continuous water sound) can waste hundreds of liters daily; minor leaks add up too. Exact extra cost depends on local water rates and leak severity. Compare water bills before and after repair.
How often to replace the flapper?
No fixed lifespan; rubber typically ages after a few years. If your toilet refills intermittently, or a dye test shows colored water, replace it. Chlorine-based tank cleaners accelerate rubber aging and are not recommended.
Do you need to turn off the main water supply to replace the fill valve?
Usually unnecessary; just turn off the angle valve behind the toilet. But if the angle valve won't turn, doesn't seal, or leaks, turn off the main valve (usually near the basement water meter), and have a professional replace the angle valve as well.
Is water around the toilet base always a sign that the toilet needs replacing?
Not necessarily. The most common cause is a damaged wax seal under the base or loose mounting bolts. Remove the toilet, replace the wax ring, and reinstall to fix. Only replace the toilet itself if it's cracked. Be aware that water could have seeped into the floor or ceiling below, so address it as soon as possible.
If you rent and the toilet leaks, who pays for repair?
Generally, tenants should notify landlords in writing promptly. Repairs are usually landlord’s responsibility per lease and Ontario rental rules. Don’t dismantle the toilet yourself to avoid liability.
Can't handle it yourself? Post a job and nearby Chinese-speaking pros will quote for free — compare before you choose.
Post a job for free